上海叶拓科技有限公司

Provide customers with high-quality precision equipment
A high-tech industry integrating R&D, production, sales and service of experimental equipment
Precautions for using Shanghai Yetuo low-temperature biochemical incubator
release time:2024-09-10  |  Browse:1513

The Shanghai Yetuo low-temperature biochemical incubator has a wide range of applications in experimental fields such as biology, agriculture, and medicine. In order to ensure the normal operation of the equipment, extend its service life, and ensure the accuracy of experimental results, the following points should be noted when using:

1. Environmental requirements

Avoid direct sunlight: The low-temperature biochemical incubator should be placed in a cool, well ventilated place, away from direct sunlight to avoid affecting internal temperature control.

Keep away from heat and moisture: Incubators should be avoided from being placed next to high-temperature equipment or in areas with high humidity. Excessive moisture can cause damage to internal electrical components, while high temperatures can affect the heat dissipation of the enclosure.

Stable placement: Ensure that the equipment is placed on a stable ground to prevent vibration or noise caused by unstable placement during operation, which may affect the cultivation effect of the sample.

2. Attention to power supply usage

Stable power supply voltage: The equipment should be connected to a stable power supply, typically 220V/50Hz. In situations where the voltage is unstable or fluctuates greatly, it is recommended to use a voltage regulator to prevent equipment damage or unstable operation caused by abnormal voltage.

Power socket: The low-temperature biochemical incubator should use a separate power socket to avoid sharing it with other high-power devices, in order to prevent power tripping or equipment failure caused by overload.

Grounding wire connection: The power plug of the equipment should have a good grounding to ensure the safety of the operator and avoid electric shock accidents caused by leakage.

3. Temperature and humidity settings

Gradually adjust the temperature: When temperature adjustment is needed, avoid setting too large a temperature difference at once. The temperature should be gradually adjusted to give sufficient time for the internal cooling or heating system to respond and avoid overloading that could affect the lifespan of the equipment.

Attention to humidity regulation: If the device is equipped with humidity control function, ensure that the water source is clean. For experiments with high humidity, regularly check and clean the water tank to prevent the growth of fine Jun or scale inside the tank, which may affect the accuracy of humidity control.

4. Sample placement requirements

Uniform placement of samples: The experimental samples should be evenly distributed on the shelf, avoiding being too concentrated in a certain position, especially not blocking the internal air duct to ensure smooth internal airflow circulation and uniformity of temperature and humidity inside the box.

Avoid too many samples: When placing samples, the incubator should not be overfilled to avoid affecting internal air circulation, resulting in uneven temperature and humidity distribution, and affecting experimental results.

5. Access control operation

Reduce the number of times the door is opened: During the experiment, the number and time of opening the box door should be minimized as much as possible. Frequent opening of doors can cause excessive fluctuations in internal temperature and humidity, affecting the cultivation effect.

Gently open and close: When opening and closing the box door, it should be operated gently to avoid excessive force that may cause a decrease in the sealing performance of the door and affect the temperature control effect of the equipment.

6. Regular maintenance of equipment

Regular cleaning of interior and exterior: The interior and exterior of the incubator should be cleaned regularly. Especially in the internal cultivation area, any spilled liquid or debris from the sample should be promptly cleaned to avoid the growth of fine particles or the generation of odors.

Maintenance of refrigeration system: The cooling holes and compressor components of the refrigeration system should be regularly cleaned to avoid dust accumulation that affects heat dissipation and equipment overheating, thereby affecting the refrigeration effect.

Maintenance of humidity control components: For equipment equipped with humidity control function, the water tank and humidity sensor should be cleaned regularly to avoid blockage by scale or pollutants that may affect the humidity control effect of the equipment.

7. Operation after power outage

Recovery operation after power outage: In the event of a power outage or unexpected power outage, the temperature, humidity, and lighting parameters of the equipment should be checked after power restoration to ensure that the system can operate normally according to the preset values. If the device has power-off memory function, it can automatically restore working parameters.

Gradually restore equipment operation: When restarting the equipment after a power outage, to avoid sudden excessive workload on the equipment, the set temperature and humidity should be gradually restored to protect the internal electrical and cooling systems.

8. Use of alarm system

Regularly check the alarm system: The temperature and humidity over limit alarm system built into the equipment needs to be checked regularly to ensure that it can promptly alert operators to handle faults in case of abnormal situations.

Pay attention to alarm signals: If the device emits an alarm, promptly check whether the internal temperature, humidity, lighting and other parameters of the device are normal, and investigate the source of the fault according to the prompt information to avoid ignoring the alarm signal and causing sample damage or equipment failure.

9. Troubleshooting and Maintenance

Regularly check the equipment status: Operators should regularly check the working status of the equipment, such as the cooling effect, whether the air duct is unobstructed, whether the buttons on the control panel are sensitive, and whether the display is normal. If any problems are found, promptly contact professional personnel for maintenance.

Professional maintenance: In case of equipment failure, do not disassemble the equipment by yourself. Contact the manufacturer or professional maintenance personnel for inspection and repair to avoid improper operation leading to the expansion of the fault or equipment damage.

10. Handling after shutdown

Regular startup inspection: If the equipment is not used for a long time, it needs to be turned on regularly to check whether all functions are normal, especially the refrigeration system and air duct circulation system, to avoid system failures caused by long-term disuse.

Turn off the power: When not in use, turn off the power and unplug the power plug, especially when it is not in use for a long time, to ensure safety and prevent damage to electrical components.

Summary:

As a widely used equipment in laboratories, the Shanghai Yetuo low-temperature biochemical incubator requires special attention to environmental conditions, power supply, temperature and humidity control, and daily maintenance during use. By reasonable operation and timely maintenance, not only can the service life of the equipment be extended, but the accuracy and reliability of the experimental results can also be ensured.

1.jpg

Previous:Application areas of Shanghai Yetuo handheld ultrasonic cell disruptor     Next:Maintenance Guide for Shanghai Yetuo Fully Automatic Open Flash Point and Ignition Point Tester
Follow us
Mobile station
  • Mobile:19961895916
  • Tel:19961895916
  • WeChat Account:上海葉拓科技
  • Email:yetuo@sh-yetuo.com
  • Address:C2-301, green window, No. 4, Lvdu Avenue
Copyright? 2025 Shanghai Yetuo Technology Co., Ltd  ICP備案號:滬ICP備20000740號-3 主站蜘蛛池模板: 上海钧尚电器有限公司 - Faulhaber电机 AMETEK pittman电机 AMETEK ROTRON军用航空风机 Exlar电动缸 MAE电机 MCG电机 CP电动工具 马头工具 AMCI驱动器 直流电机 减速箱 直流伺服电机,无刷电机,直线电机 直流防爆电机 防爆电机 汽车助力转向电机 EPS电机 faulhaber motor faulhaber gearbox NANOTEC电机 ELWOOD电机 PHYTRON电机 EXLAR伺服电动缸 高力矩、高性能直流电机,音圈电机,风机,直流风机,航空风机 | 青砖厂家,青瓦价格-河北祥庆烧结瓦有限公司 | 临沂网站建设,临沂网站制作,临沂网络公司,临沂小程序开发,临沂网站设计,沂水网站建设,沂南网站建设,蒙阴网站建设,平邑网站建设,费县网站建设,兰陵网站建设,郯城网站建设,临沭网站建设,莒南网站建设,兰山网络公司 | 精细筛-振动筛-滚筒筛-摇摆筛-平面回转筛-筛分机械设备-新乡德科筛分机械公司 | 无锡纯铁-中纯特钢纯铁公司 | 球形钢支座,粘滞阻尼器,抗震球型钢支座,盆式橡胶支座,调谐质量阻尼器,屈曲约束支撑-衡水路泽科技 | 紫外线光疗仪|白癜风光疗仪|牛皮癣治疗仪|308纳米led|SIGMA|上海希格玛高技术有限公司 | 鑫金牛建设工程(苏州)有限公司 | 天津翻译公司盖章|022-58385822| 翰文博译(天津)商务咨询有限公司 | 水热反应釜厂家_水热反应釜价格_水热合成反应釜批发-仪贝尔仪器 - 水热釜,水热反应釜,水热反应釜厂家,水热反应釜价格,水热反应釜型号,水热反应釜内衬,水热反应釜25ml,水热反应釜50ml,水热反应釜100ml,水热合成反应釜 | 墙板_户外墙板_ASA共挤户外墙板-康亿家生态木业集团 | 投影仪配件,苏州投影仪维修,B60数显表维修-苏州市加野仪器有限公司 | 中频感应加热设备_高频感应加热电源厂家_高频淬火设备_容大电源 中派康明斯发电机_玉柴发电机厂家_静音移动拖车发电机-深圳市斯坦福电力设备有限公司 | 造型松|泰山迎客松|造型油松-泰安小苹果园林 | 气泡膜机_气垫膜机_缠绕膜机_瑞安市优特机械厂 | 振动筛|不锈钢振动筛|振动筛生产厂家-新乡市大汉振动机械有限公司 | 无塔供水_无塔供水设备_全自动_石家庄工泉水处理设备有限公司_家用无塔供水器 | 桐城_池州_枞阳_黄山_潜山_东至挖掘机租赁-安庆光兴机械租赁有限公司 | 联系我们-99公司开户电话-99厅 | 买化工,找万创!泉州万创化工贸易有限公司 | 中国环博会 | 亚洲旗舰环保展 2025.4.21-23 上海新国际博览中心 中国焊接协会网站—中国焊接信息网;焊接行业最权威访问量最大的专业网站:焊接信息、焊接材料,焊接机器,焊接设备,焊机,焊材,辅助设备,焊机配件,仪器仪表,电动工具,钎焊,送丝机,表面处理,自动化专机,焊锡丝,助焊剂 | 和中出国移民官网|出国移民|加拿大移民|欧洲移民|爱尔兰移民|马耳他移民|希腊移民|美国移民|海外护照_和中移民 | 陶瓷颗粒厂家_彩色路面_彩色陶瓷颗粒-山东顺驰道路材料有限公司 陶瓷复合钢管-专业提供江苏陶瓷钢管和陶瓷内衬复合钢管的生产厂家 | 上进电缆(嘉兴)股份有限公司官网 - 光伏电缆|防火电缆|电力电缆|铝合金电缆专业生产厂家 | 柔性防水套管_刚性防水套管-河南恒生管道制造有限公司 | 威海赶海网、乳山特产、威海专营海产品、威海旅游产品 - 威海赶海电子商务 | 软文营销推广-新闻稿发布-软文撰写-百科词条编辑-品牌全案策划推广网络营销传播-喜尚传媒 | 莱湾科技-智能会议室|多功能|多媒体|音视频|无纸化|远程视频会议室运维 | 耐磨钢板_复合耐磨板_KN60耐磨钢板-北京耐默公司 | 内蒙古碧云食品有限公司| 墨子百科-专业有趣的问题小百科 莫非传媒官网-江西知名的网络营销推广服务平台南昌网络公司,专业网络公关,品牌危机处理,网站SEO优化,微信朋友圈广告,网站建设,南昌莫非文化传媒有限公司 | 矿用三环链|锻打/焊接三环链|矿车万能环|三环链销子-济宁卓力工矿设备有限公司 | 中科联航(江苏)-信息化监理|信息化咨询|信息系统项目管理|信息系统工程监理公司 | 深圳固派克包装机械科技有限公司_封口收缩机_封箱机-捆包机-缠膜机 | 域发官网-皮肤学级头皮养固领先者| 耀美软瓷施工队-13638350103-专注于软瓷施工勾缝的贴软瓷施工队 - 软瓷,软瓷施工,软瓷勾缝,软瓷怎么施工,软瓷怎么勾缝,贴软瓷,软瓷施工队 | 金属探测机_食品金属探测仪_食品金属探测器_广东善安金属检测机 金属剪切机,金属打包机,废钢剪切机,废铁压块机,金属压块机,废纸打包机,重废龙门剪,废钢龙门剪,箱式剪,液压剪切机-瑞顿机械装备制造江阴有限公司 | 自动封箱机_纸箱封箱机_封箱机厂家-青岛百高包装器材有限公司 | 上海商标注册,上海注册商标,上海商标代理,国际商标注册,版权登记-上海律点知识产权代理有限公司 上海山田机械有限公司 | 塑料检查井_双扣聚氯乙烯增强管_双壁波纹管-河南中盈塑料制品有限公司 | 泥浆振动筛|卧式泥浆搅拌器|泥浆离心机|泥浆处理固控设备_沧州宏宇石油机械有限公司 |